Next Previous Contents

15. Examples of use of loadkeys and xmodmap

Switching Caps Lock and Control on the keyboard (assuming you use keymaps 0-15; check with dumpkeys | head -1) 

        % loadkeys
        keymaps 0-15
        keycode 58 = Control
        keycode 29 = Caps_Lock
        %
Switching them under X only: 
        % xmodmap .xmodmaprc
where .xmodmaprc contains lines 
        remove Lock = Caps_Lock
        remove Control = Control_L
        keysym Control_L = Caps_Lock
        keysym Caps_Lock = Control_L
        add Lock = Caps_Lock
        add Control = Control_L
What is this about the key numbering? Backspace is 14 under Linux, 22 under X? Well, the numbering can best be regarded as arbitrary; the Linux number of a key can be found using showkey(1), and the X number using xev(1). Often the X number will be 8 more than the Linux number.

Something else people like to change are the bindings of the function keys. Suppose that you want to make F12 produce the string "emacs ". Then 

        % loadkeys
        keycode 88 = F12
        string F12 = "emacs "
        %
will do this. More explicitly, the procedure is like this: (i) find the keycodes of the keys to be remapped, using showkey(1). (ii) save the current keymap, make a copy and edit that: 
        % dumpkeys > my_keymap
        % cp my_keymap trial_keymap
        % emacs trial_keymap
        % loadkeys trial_keymap
        %
The format of the table can be guessed by looking at the output of dumpkeys, and is documented in keymaps(5). When the new keymap functions as desired, you can put an invocation 
        loadkeys my_new_keymap
in /etc/rc.local or so, to execute it automatically at boot-up. Note that changing modifier keys is tricky, and a newbie can easily get into a situation only an expert can get out of.

The default directory for keymaps is /usr/lib/kbd/keymaps. The default extension for keymaps is .map. For example, loadkeys uk would probably load /usr/lib/kbd/keymaps/i386/qwerty/uk.map. (With kbd-0.95 and older this would be /usr/lib/kbd/keytables and /usr/lib/kbd/keytables/uk.map.)

(On my machine) /dev/console is a symbolic link to /dev/tty0, and the kernel regards /dev/tty0 as a synonym for the current VT. XFree86 1.3 changes the owner of /dev/tty0, but does not reset this after finishing. Thus, loadkeys or dumpkeys might fail because someone else owns /dev/tty0; in such a case you might run X first. Note that you cannot change keyboard mappings when not at the console (and not superuser).

15.1 `I can use only one finger to type with'

"Can the Shift, Ctrl and Alt keys be made to behave as toggles?"

Yes, after saying 

        % loadkeys
        keymaps 0-15
        keycode 29 = Control_Lock
        keycode 42 = Shift_Lock
        keycode 56 = Alt_Lock
        %
the left Control, Shift and Alt keys will act as toggles. The numbers involved are revealed by showkey (and usually are 29, 97, 42, 54, 56, 100 for left and right control, shift and alt, respectively), and the functions are Control_Lock, Shift_Lock, Alt_Lock, ALtGr_Lock.

"What about `sticky' modifier keys?"

Since version 1.3.33, the kernel knows about `sticky' modifier keys. These act on the next key pressed. So, where one earlier needed the 3-symbol sequence Shift_Lock a Shift_Lock to type `A', one can now use the 2-symbol sequence SShift_Lock a. You can say 

        % loadkeys
        keymaps 0-15
        keycode 54 = SShift
        keycode 97 = SCtrl
        keycode 100 = SAlt
        %
to make the right Shift, Ctrl, Alt sticky versions of the left ones. This will allow you to type Ctrl-Alt-Del in three keystrokes with one hand.

The keymaps line in these examples should cover all keymaps you have in use. You find what keymaps you have in use by 

        % dumpkeys | head -1

15.2 Sticky keys under X

The following text was contributed by Piotr Mitros.

XFree86 supports an accessibility option which allows disabled users to type single-handed. With sticky keys enabled, the user can hit a modifier key (ctrl, alt, shift) followed by another key, rather than having to hold the modifier key while hitting the letter.

To enable sticky keys, first make sure the xkb extension is enabled (this is done during initial X server configuration and is usually enabled by default). Next, run the X server with the +accessx option. If you use startx, either run startx -- +accessx or add +accessx to the serverargs line in the startx script. If you use xdm, add +accessx to the appropriate server line in /etc/X11/xdm/Xservers.

It is also possible to enable X accessibility with some end-user utilities with a running X server.

Once X accessibility is enabled, press the shift key five times in a row to enable sticky keys. To disable sticky keys, either press the shift key five times again, or press a key while holding a modifier key.

XFree86 also supports Slow Keys, Repeat Keys, Bounce Keys and an audible bell. xkbcomp can be used to generate a .xkm file to enable these. The appropriate xkbcomp commands are listed in /usr/X11R6/lib/X11/xkb/compat/accessx. Unfortunately, the exact process is still undocumented.

Next Previous Contents